Відео

is recommendable to have cause if the battery dies you have to start over again

yes it will

@@JVFIXLLC thank , it worked !

no problem

GC3Z-5L239-A yea is the same. the link is in the description

yea so sorry about I already fixed that problem on my future videos bad editing skills

check the fuse# 4 it is a 40amp green fuse on the front left side of the engine. thats the fuse for the blower motor

no problem bro

from a company called www.autotechelectronic.com , but i think they raised the price i am probably thinking on opening my own website and sell them more cheap.

i left the link in the description amazon sells it

pretty much you have the same issue but doing a good diagnostic it can be determined what is causing that code.

i use the autel im608 and is a bit expensive but i have a review on a new scanner i just got and it does the same functions and is more affordable

then you could have a defective key

yea! remove the belt and spin the pulley i am pretty sure you have the same issue

thanks

if adding no need to remove anything only when is all keys lost

@@JVFIXLLC Then I just need adapter to obd connector

yea that actually was the most difficult part i spent like 1 hour to get it out.

I am in visalia California

i would say that one would be close to 880 or a bit more because your model uses the 1234y special freon and it needs a special machine to recover the ac and charge it if it was older it would have been like 500 bucks

yea it did

You're welcome!

Thanks 👍

Nice work!

I am in visalia California

yes it can but you will need to get the programmer which is separate from this tool.

@@JVFIXLLC which programmer because am about to buy the launch scanner

this is the only way I know that it can be done

yea great scanner and cheap

@@JVFIXLLC yes I have ssame scanner,,very nice

si si esta

unfortunately I Don't work at that shop anymore but the process is the same

yea is the same process but on manual you have to put it in first and force the rpms to go lower using the clutch

dang maybe your apim might be failing specially in the heat like California

have u check the fuse?

@@JVFIXLLC no but that's a good idea, I'm going to check the fuse and the relay cuz that's probably what it is

@timobatana6705 yea cause if the resistor was bad it probably burned the fuse

@@JVFIXLLC ahhh good to know. Thank you. That helps because I was thinking about taking the resistor back but I'll keep the new one

no problem

posiblemente si voy a ver si el scanner sporta ese an̈o

then I am afraid u will need a scanner or a locksmith do it. sorry

@@JVFIXLLC thanks

lol

yea it can do it

@@JVFIXLLC That's great! So it works with gasoline engines too, and not only diesel like the Ram 3.0 and Ford 6.7 you did? Have you checked on a 2022 Camry to confirm?

yea the link for the part I used is in the description

do you need to program it or on what step you are stuck?

I Don't have much experience with that one but I have heard is good.

what do you mean?

force the inner door panel to come off that's the only way

best way to move is disconnecting the speed sensor that goes on the tranny and it will let u move but there is a risk that I could damage the tranny cause it won't shift good when u disconnect it and then start driving

@@JVFIXLLC ок i thought your speed on video was 50mph. I did the procedure, heated the EGT 14 to 450 degrees, turned off the car for two minutes, started it again, made sure the injector readings did not rise, then moved 5 mph, made 5 accelerations from 0 to 5 mph, put it in park and the car idled for 30 minutes, after that the error message still hangs, did I do everything right? or did I miss something somewhere?

@@JVFIXLLC repeat the procedure from what point? Should I heat everything up again or just start moving and try to speed up? What should acceleration look like from a complete stop or after starting to move, always keep your foot on the gas pedal and release the gas pedal and press it again?

@@JVFIXLLC ?

Even with an impact? Did you try to heat it with a torch?

no problem

I use aftermarket chips and they work really good. if u have original key and just making a copy u can start your vehicle with your original key and then turn it off and then turn it on but now with the key that u want to program

@JVFIXLLC hello I actually lost original key and now not sure if the new transponder key or the new key with circuit chip can be programmed without any programming tool for my chevrolet spin model. Do you have any idea ? Thanks

it depends on the car like mercedes when they get in an accident the fuse in the front of the hoods pops to avoid electrical shorts that can cause a fire.

I got it to start bad intake gasket had water in cylinders new sparkplugs fired right up

it needs to be reprogrammed.

debe quedar en on y apagarse el testigo rojo

in my case I use pro scanners like autel im608 and otofix im2 because I work on multiple brands and models but there some brands out there of scanners. what car u want to program?

no problema gracias por visitar el canal saludos